Skip to content

micro-ROS/micro_ros_setup

Repository files navigation



This ROS 2 package is the entry point for building micro-ROS apps for different embedded platforms.

Supported platforms

This package provides tools and utils to crosscompile micro-ROS with just the common ROS 2 tools for the following platforms platforms.

Note that this package provides basic support only, intended in particular for ROS developers who are new to microcontrollers. Micro-ROS components for each platform are available and provide a deeper and more flexible integration with the platform-specific build systems.

RTOS Platform Version Example Recommended Alternative
FreeRTOS ST Nucleo F446RE 1 STM32CubeMX latest freertos nucleo_f446re micro-ROS utils for STM32CubeMX and STM32CubeIDE
FreeRTOS ST Nucleo F446ZE 1 STM32CubeMX latest freertos nucleo_f446ze micro-ROS utils for STM32CubeMX and STM32CubeIDE
FreeRTOS ST Nucleo F746ZG 1 STM32CubeMX latest freertos nucleo_f746zg micro-ROS utils for STM32CubeMX and STM32CubeIDE
FreeRTOS ST Nucleo F767ZI 1 STM32CubeMX latest freertos nucleo_f767zi micro-ROS utils for STM32CubeMX and STM32CubeIDE
FreeRTOS Espressif ESP32 v8.2.0 freertos esp32 micro-ROS component for ESP-IDF
FreeRTOS Crazyflie 2.1 v10.2.1 - CF 2020.06 freertos crazyflie21
Zephyr Olimex STM32-E407 v2.6.0 zephyr olimex-stm32-e407 micro-ROS module for Zephyr RTOS
Zephyr ST Nucleo F446RE 1 v2.6.0 zephyr nucleo_f446re micro-ROS module for Zephyr RTOS
Zephyr ST B-L475E-IOT01A v2.6.0 zephyr discovery_l475_iot1 micro-ROS module for Zephyr RTOS
Zephyr ST Nucleo H743ZI 1 v2.6.0 zephyr nucleo_h743zi micro-ROS module for Zephyr RTOS
Zephyr Zephyr emulator v2.6.0 zephyr host micro-ROS module for Zephyr RTOS
Linux Host 2 Ubuntu 18.04/20.04 host
Android AOSP 1 Latest android generic

1 Community supported, may have lack of official support

2 Support for compiling apps in a native Linux host for testing and debugging

3 a valid CMake toolchain with custom crosscompilation definition is required

Standalone build system tools

micro_ros_setup provides access to standalone build system tools using the component command. After building this package just run:

ros2 run micro_ros_setup component --help

micro-ROS standalone module for specific platforms are:

Dependencies

This package targets the ROS 2 installation. ROS 2 supported distributions are:

ROS 2 Distro State Branch
Crystal EOL crystal
Dashing EOL dashing
Foxy EOL foxy
Galactic EOL galactic
Humble Supported humble
Iron Supported iron
Jazzy Supported jazzy
Rolling Supported rolling

Some other prerequisites needed for building a firmware using this package are:

sudo apt install python3-rosdep

Building for Android needs Latest Android NDK to be installed and the following environment variables to be set:

  • ANDROID_ABI: CPU variant, refer here for details.
  • ANDROID_NATIVE_API_LEVEL: Android platform version, refer here for details.
  • ANDROID_NDK: root path of the installed NDK.

Quick start

Download here the micro-ROS docker image that contains a pre-installed client and agent as well as some compiled examples.

Building

Create a ROS 2 workspace and build this package for a given ROS 2 distro (see table above):

source /opt/ros/$ROS_DISTRO/setup.bash

mkdir uros_ws && cd uros_ws

git clone -b $ROS_DISTRO https://github.com/micro-ROS/micro_ros_setup.git src/micro_ros_setup

rosdep update && rosdep install --from-paths src --ignore-src -y

colcon build

source install/local_setup.bash

Once the package is built, the firmware scripts are ready to run.

You can find tutorials for moving your first steps with micro-ROS on an RTOS in the micro-ROS webpage.

Creating micro-ROS firmware

Using the create_firmware_ws.sh [RTOS] [Platform] command, a firmware folder will be created with the required code for building a micro-ROS app. For example, for our reference platform, the invocation is:

# Creating a FreeRTOS + micro-ROS firmware workspace
ros2 run micro_ros_setup create_firmware_ws.sh freertos olimex-stm32-e407

# Creating a Zephyr + micro-ROS firmware workspace
ros2 run micro_ros_setup create_firmware_ws.sh zephyr olimex-stm32-e407

Configuring micro-ROS firmware

By running configure_firmware.sh command the installed firmware is configured and modified in a pre-build step. This command will show its usage if parameters are not provided:

ros2 run micro_ros_setup configure_firmware.sh [configuration] [options]

By running this command without any argument the available demo applications and configurations will be shown.

Common options available at this configuration step are:

  • --transport or -t: udp, serial or any hardware specific transport label
  • --dev or -d: agent string descriptor in a serial-like transport (optional)
  • --ip or -i: agent IP in a network-like transport (optional)
  • --port or -p: agent port in a network-like transport (optional)

Please note that each RTOS has its configuration approach that you might use for further customization of these base configurations. Visit the micro-ROS webpage for detailed information about RTOS configuration.

In summary, the supported configurations for transports are:

FreeRTOS Zephyr
Olimex STM32-E407 UART, Network USB, UART
ST B-L475E-IOT01A - USB, UART, Network
Crazyflie 2.1 Custom Radio Link -
Espressif ESP32 UART, WiFI UDP -
ST Nucleo F446RE 1 UART UART
ST Nucleo F446ZE 1 UART -
ST Nucleo H743ZI 1 - UART
ST Nucleo F746ZG 1 UART UART
ST Nucleo F767ZI 1 UART -

1 Community supported, may have lack of official support

Building micro-ROS firmware

By running build_firmware.sh the firmware is built:

ros2 run micro_ros_setup build_firmware.sh

Flashing micro-ROS firmware

In order to flash the target platform run flash_firmware.sh command. This step may need some platform-specific procedure to boot the platform in flashing mode:

ros2 run micro_ros_setup flash_firmware.sh

Building micro-ROS-Agent

Using this package is possible to install a ready to use micro-ROS-Agent:

ros2 run micro_ros_setup create_agent_ws.sh
ros2 run micro_ros_setup build_agent.sh
source install/local_setup.sh
ros2 run micro_ros_agent micro_ros_agent [parameters]

Contributing

As it is explained along this document, the firmware building system takes four steps: creating, configuring, building and flashing.

New combinations of platforms and RTOS are intended to be included in config folder. For example, the scripts for building a micro-ROS app for Crazyflie 2.1 using FreeRTOS is located in config/freertos/crazyflie21.

This folder contains up to four scripts:

  • create.sh: gets a variable named $FW_TARGETDIR and installs in this path all the dependencies and code required for the firmware.
  • configure.sh: modifies and configure parameters of the installed dependencies. This step is optional.
  • build.sh: builds the firmware and create a platform-specific linked binary.
  • flash.sh: flashes the binary in the target platform.

Some other required files inside the folder can be accessed from these scripts using the following paths:

# Files inside platform folder
$PREFIX/config/$RTOS/$PLATFORM/

# Files inside config folder
$PREFIX/config

Purpose of the Project

This software is not ready for production use. It has neither been developed nor tested for a specific use case. However, the license conditions of the applicable Open Source licenses allow you to adapt the software to your needs. Before using it in a safety relevant setting, make sure that the software fulfills your requirements and adjust it according to any applicable safety standards, e.g., ISO 26262.

License

This repository is open-sourced under the Apache-2.0 license. See the LICENSE file for details.

For a list of other open-source components included in ROS 2 system_modes, see the file 3rd-party-licenses.txt.

Known Issues / Limitations

There are no known limitations.

If you find issues, please report them.

Papers

If you want to cite micro-ROS, please cite the following book chapter (PDF available at Springer Link):

Kaiwalya Belsare, Antonio Cuadros Rodriguez, Pablo Garrido Sánchez, Juanjo Hierro, Tomasz Kołcon, Ralph Lange, Ingo Lütkebohle, Alexandre Malki, Jaime Martin Losa, Francisco Melendez, Maria Merlan Rodriguez, Arne Nordmann, Jan Staschulat, and Julian von Mendel: Micro-ROS. In: Anis Koubaa (ed.) Robot Operating System (ROS): The Complete Reference (Volume 7), Springer, pp. 3–55, 2023. (Online since 2 February 2023.)

@INBOOK{Belsare_et_al_2023_Micro-ROS,
  author = {Kaiwalya Belsare and Antonio Cuadros Rodriguez and Pablo Garrido S\'{a}nchez and Juanjo Hierro
            and Tomasz Ko\l{}con and Ralph Lange and Ingo L\"{u}tkebohle and Alexandre Malki
            and Jaime Martin Losa and Francisco Melendez and Maria Merlan Rodriguez and Arne Nordmann
            and Jan Staschulat and and Julian von Mendel},
  title = {Micro-ROS},
  editor = {Anis Koubaa},
  booktitle = {Robot Operating System (ROS): The Complete Reference (Volume 7)},
  year = {2023},
  publisher = {Springer},
  pages = {3--55},
  doi = {10.1007/978-3-031-09062-2_2}
}