-
Notifications
You must be signed in to change notification settings - Fork 11
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
Add Nylon spacers to the BOM for the Duet and Duex5 #13
Comments
Should likely just upload the printable ones I've been using and add them
to the parts list.
…On Tue, Jun 4, 2019 at 4:05 PM Dan White ***@***.***> wrote:
As title. Self-sourcers can get stuck on that bit if they don't have
standoffs "in stock"
—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub
<#13?email_source=notifications&email_token=ABYQQ4YUOEVQ327M6KHQZU3PY3DJLA5CNFSM4HTA73WKYY3PNVWWK3TUL52HS4DFUVEXG43VMWVGG33NNVSW45C7NFSM4GXTYN6A>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/ABYQQ45VMAZUANBS2UXYDMTPY3DJLANCNFSM4HTA73WA>
.
|
I made some brackets with heat-set inserts on both sides so that you can screw the brackets through the side panel and then screw the duet/duex into the bracket. Makes assembly a lot easier than spacers and nuts - might be something we should entertain "upstream" as well? |
I've considered modeling a duet + duex5 "holder" that has integrated wire
minders, so it tidies it all up nicely. But it's been "on the list" for
over a year now.
…On Tue, Jun 4, 2019 at 4:27 PM Joe Francis ***@***.***> wrote:
I made some brackets with heat-set inserts on both sides so that you can
screw the brackets through the side panel and then screw the duet/duex into
the bracket. Makes assembly a lot easier than spacers and nuts - might be
something we should entertain "upstream" as well?
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#13?email_source=notifications&email_token=ABYQQ47CT2ADQQES2O3RN7LPY3F4ZA5CNFSM4HTA73WKYY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGODW5YZJQ#issuecomment-498830502>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/ABYQQ4Y3XUNMQD4FQ7VMGFTPY3F4ZANCNFSM4HTA73WA>
.
|
@kraegar printable ones will be a reasonable step to start with. Do you have a link to the ones you used to save me digging through Thingiverse? |
Added to thingiverse and the BOM parts list
…On Wed, Jun 5, 2019 at 4:16 AM Dan White ***@***.***> wrote:
@kraegar <https://github.com/kraegar> printable ones will be a reasonable
step to start with. Do you have a link to the ones you used to save me
digging through Thingiverse?
They can then be added to the parts repo and to the docs
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#13?email_source=notifications&email_token=ABYQQ45QDYNVBMSUJQVWDIDPY5Y6TA5CNFSM4HTA73WKYY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGODW66SMI#issuecomment-498985265>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/ABYQQ45JKEVAKWUDTZ53NNLPY5Y6TANCNFSM4HTA73WA>
.
|
Nice one. I've added that to the parts repo too. |
As title. Self-sourcers can get stuck on that bit if they don't have standoffs "in stock"
The text was updated successfully, but these errors were encountered: