4.3.0 with AKK / RDQ smartaudio fix

Continuation of the older 4.2 branch https://github.com/betaflight/betaflight/tree/akk_vtx_fix but ported to 4.3.0

Fix adds trailing bytes to the smartaudio data to be compatible with early AKK / RDQ smartaudio VTXs.

Betaflight Configurator 10.8.0 release or newer is required to configure Betaflight 4.3: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults

4.3.0 for DJI with LQ & RSSI & warnings

• Updated BetaFlight to 4.3.0 final and re-applied patches.
• Warnings shown in CRAFT_NAME field
• When no warning is shown, LQ & RSSI-dBm are shown
• Added LQ, flight mode and RSSI dBm value for CRSF protocol
• Zero-padded LQ percent so it doesn't jump going 100 to 99
• Added LQ and RSSI dBm for Ghost protocol - If you use GHST you only see "LQ 100 -20" with no flight mode!
• Blinking warnings added - LQ/RSSI only hidden 1/2 the time as warning now blinks instead of always covering LQ/RSSI (you may need to select PAL or NTSC instead of AUTO to get the blink speed to be consistent).

Betaflight Configurator 10.8.0 release or newer is required to configure Betaflight 4.3: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0

This patch takes the craft name field and replaces it's value with a "LQ:1:100 -50" or similar value.

If a warning is present then this will flash over the LQ/RSSI.

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults
6. Go to OSD tab.
   • enable warnings OSD element
   • enable LQ OSD element
   • enable craft-name OSD element and place craft-name where you want to see LQ & warnings
   • make sure you've disabled the analogue channel for RSSI!

4.3.0-RC7 with AKK / RDQ smartaudio fix

Continuation of the older 4.2 branch https://github.com/betaflight/betaflight/tree/akk_vtx_fix but ported to 4.3.0-RC7

Fix adds trailing bytes to the smartaudio data to be compatible with early AKK / RDQ smartaudio VTXs.

Betaflight 4.3.0 is unreleased software and has not been fully tested. Please take care when testing this.

Betaflight Configurator RC7 release or newer is required to configure Betaflight 4.3 RC7: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0-RC7

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults

4.3.0-RC7 for DJI with LQ & RSSI & warnings

• Updated BetaFlight to 4.3.0-RC7 and re-applied patches.
• Warnings shown in CRAFT_NAME field
• When no warning is shown, LQ & RSSI-dBm are shown
• Added LQ, flight mode and RSSI dBm value for CRSF protocol
• Zero-padded LQ percent so it doesn't jump going 100 to 99
• Added LQ and RSSI dBm for Ghost protocol - If you use GHST you only see "LQ 100 -20" with no flight mode!
• Blinking warnings added - LQ/RSSI only hidden 1/2 the time as warning now blinks instead of always covering LQ/RSSI (you may need to select PAL or NTSC instead of AUTO to get the blink speed to be consistent).

Betaflight 4.3.0 is unreleased software and has not been fully tested. Please take care when testing this.

Betaflight Configurator RC7 release or newer is required to configure Betaflight 4.3 RC7: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0-RC7

This patch takes the craft name field and replaces it's value with a "LQ:1:100 -50" or similar value.

If a warning is present then this will flash over the LQ/RSSI.

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults
6. Go to OSD tab.
   • enable warnings OSD element
   • enable LQ OSD element
   • enable craft-name OSD element and place craft-name where you want to see LQ & warnings
   • make sure you've disabled the analogue channel for RSSI!

4.3.0-RC6 for DJI with LQ & RSSI & warnings

• Updated BetaFlight to 4.3.0-RC6 and re-applied patches.
• Warnings shown in CRAFT_NAME field
• When no warning is shown, LQ & RSSI-dBm are shown
• Added LQ, flight mode and RSSI dBm value for CRSF protocol
• Zero-padded LQ percent so it doesn't jump going 100 to 99
• Added LQ and RSSI dBm for Ghost protocol - If you use GHST you only see "LQ 100 -20" with no flight mode!
• Blinking warnings added - LQ/RSSI only hidden 1/2 the time as warning now blinks instead of always covering LQ/RSSI (you may need to select PAL or NTSC instead of AUTO to get the blink speed to be consistent).

Betaflight 4.3.0 is unreleased software and has not been fully tested. Please take care when testing this.

Betaflight Configurator RC6 release or newer is required to configure Betaflight 4.3 RC6: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0-RC6

This patch takes the craft name field and replaces it's value with a "LQ:1:100 -50" or similar value.

If a warning is present then this will flash over the LQ/RSSI.

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults
6. Go to OSD tab.
   • enable warnings OSD element
   • enable LQ OSD element
   • enable craft-name OSD element and place craft-name where you want to see LQ & warnings
   • make sure you've disabled the analogue channel for RSSI!

4.3.0-RC5 for DJI with LQ & RSSI & warnings

• Updated BetaFlight to 4.3.0-RC5 and re-applied patches.
• Warnings shown in CRAFT_NAME field
• When no warning is shown, LQ & RSSI-dBm are shown
• Added LQ, flight mode and RSSI dBm value for CRSF protocol
• Zero-padded LQ percent so it doesn't jump going 100 to 99
• Added LQ and RSSI dBm for Ghost protocol - If you use GHST you only see "LQ 100 -20" with no flight mode!
• Blinking warnings added - LQ/RSSI only hidden 1/2 the time as warning now blinks instead of always covering LQ/RSSI (you may need to select PAL or NTSC instead of AUTO to get the blink speed to be consistent).

Betaflight 4.3.0 is unreleased software and has not been fully tested. Please take care when testing this.

Betaflight Configurator RC5 release or newer is required to configure Betaflight 4.3 RC5: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0-RC5

This patch takes the craft name field and replaces it's value with a "LQ:1:100 -50" or similar value.

If a warning is present then this will flash over the LQ/RSSI.

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults
6. Go to OSD tab.
   • enable warnings OSD element
   • enable LQ OSD element
   • enable craft-name OSD element and place craft-name where you want to see LQ & warnings
   • make sure you've disabled the analogue channel for RSSI!

4.3.0-RC4 for DJI with LQ & RSSI & warnings

Added eLRS targets for people building 1S digital quads.

• Updated BetaFlight to 4.3.0-RC4 and re-applied patches.
• Warnings shown in CRAFT_NAME field
• When no warning is shown, LQ & RSSI-dBm are shown
• Added LQ, flight mode and RSSI dBm value for CRSF protocol
• Zero-padded LQ percent so it doesn't jump going 100 to 99
• Added LQ and RSSI dBm for Ghost protocol - If you use GHST you only see "LQ 100 -20" with no flight mode!
• Blinking warnings added - LQ/RSSI only hidden 1/2 the time as warning now blinks instead of always covering LQ/RSSI (you may need to select PAL or NTSC instead of AUTO to get the blink speed to be consistent).

Betaflight 4.3.0 is unreleased software and has not been fully tested. Please take care when testing this.

Betaflight Configurator RC4 release or newer is required to configure Betaflight 4.3 RC4: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0-RC4

This patch takes the craft name field and replaces it's value with a "LQ:1:100 -50" or similar value.

If a warning is present then this will flash over the LQ/RSSI.

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults
6. Go to OSD tab.
   • enable warnings OSD element
   • enable LQ OSD element
   • enable craft-name OSD element and place craft-name where you want to see LQ & warnings
   • make sure you've disabled the analogue channel for RSSI!

4.3.0-RC3 for DJI with LQ & RSSI & warnings

Apologies for the delay on this release, here at last is the RC3 update for Betaflight DJI OSD

• Updated BetaFlight to 4.3.0-RC3 and re-applied patches.
• Warnings shown in CRAFT_NAME field
• When no warning is shown, LQ & RSSI-dBm are shown
• Added LQ, flight mode and RSSI dBm value for CRSF protocol
• Zero-padded LQ percent so it doesn't jump going 100 to 99
• Added LQ and RSSI dBm for Ghost protocol - If you use GHST you only see "LQ 100 -20" with no flight mode!
• Blinking warnings added - LQ/RSSI only hidden 1/2 the time as warning now blinks instead of always covering LQ/RSSI (you may need to select PAL or NTSC instead of AUTO to get the blink speed to be consistent).

Betaflight 4.3.0 is unreleased software and has not been fully tested. Please take care when testing this.

Betaflight Configurator RC3 release or newer is required to configure Betaflight 4.3 RC3: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0-RC3

This patch takes the craft name field and replaces it's value with a "LQ:1:100 -50" or similar value.

If a warning is present then this will flash over the LQ/RSSI.

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults
6. Go to OSD tab.
   • enable warnings OSD element
   • enable LQ OSD element
   • enable craft-name OSD element and place craft-name where you want to see LQ & warnings
   • make sure you've disabled the analogue channel for RSSI!

4.3.0-RC2 for DJI with LQ & RSSI & warnings - blinking

• Updated BetaFlight to 4.3.0-RC2 and re-applied patches.
• Warnings shown in CRAFT_NAME field
• When no warning is shown, LQ & RSSI-dBm are shown
• Added LQ, flight mode and RSSI dBm value for CRSF protocol
• Zero-padded LQ percent so it doesn't jump going 100 to 99
• Added LQ and RSSI dBm for Ghost protocol - If you use GHST you only see "LQ 100 -20" with no flight mode!
• Blinking warnings added - LQ/RSSI only hidden 1/2 the time as warning now blinks instead of always covering LQ/RSSI

Betaflight 4.3.0 is unreleased software and has not been fully tested. Please take care when testing this.

Betaflight Configurator RC1 release or newer is required to configure Betaflight 4.3 RC2: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0-RC2

This patch takes the craft name field and replaces it's value with a "LQ:1:100 -50" or similar value.

If a warning is present then this will flash over the LQ/RSSI.

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults
6. Go to OSD tab.
   • enable warnings OSD element
   • enable LQ OSD element
   • enable craft-name OSD element and place craft-name where you want to see LQ & warnings
   • make sure you've disabled the analogue channel for RSSI!

4.3.0-RC2 for DJI with LQ & RSSI & warnings

• Updated BetaFlight to 4.3.0-RC2 and re-applied patches.
• Warnings shown in CRAFT_NAME field
• When no warning is shown, LQ & RSSI-dBm are shown
• Added LQ, flight mode and RSSI dBm value for CRSF protocol
• Zero-padded LQ percent so it doesn't jump going 100 to 99
• Added LQ and RSSI dBm for Ghost protocol

Betaflight 4.3.0 is unreleased software and has not been fully tested. Please take care when testing this.

Betaflight Configurator RC1 release or newer is required to configure Betaflight 4.3 RC2: https://github.com/betaflight/betaflight-configurator/releases/tag/10.8.0-RC2

This patch takes the craft name field and replaces it's value with a "LQ:1:100 -50" or similar value.

If a warning is present then this will flash over the LQ/RSSI.

Installation:

1. Backup a diff of your config in betaflight, in CLI do diff all
   • the paranoid among you may wish to do a dump if you are running a non-official firmware e.g. a vendor-built firmware.
2. Download firmware below matching your flight controller MCU model.
3. Open Configurator 10.8.0+ and select your FC model
4. Flash the firmware - in Betaflight Configurator Firmware Updater choose "local file"
5. If your diff is from 4.3 put it all in, otherwise you can put in most things except the PID and filter sections.
   • some config items have changed names during 4.3 development including slider names, if your 4.3 config is older you may need to reset the some sliders to defaults
6. Go to OSD tab.
   • enable warnings OSD element
   • enable LQ OSD element
   • enable craft-name OSD element and place craft-name where you want to see LQ & warnings
   • make sure you've disabled the analogue channel for RSSI!