CHANGELOG

## Changelog:

#### 1.26.08
- MapleCUN: Fix serial2net

#### 1.26.07
- MapleCUN/CUBe: MSC bootloader
- CUBe: Bugfix HW autodetect

#### 1.26.06
- MapleCUN/CUBe: Bugfix repeated messages filter
- MapleCUN/CUBe: Autodetect onewire on any CC port
- MapleCUN: Changed to bus powered USB configuration descriptor

#### 1.26.05
- MapleCUN: Fix CDC

#### 1.26.04
- CUBe: added HMS Device Emulation for LaCrosse

#### 1.26.03
- I2CCUL: changed Protocol definition
- MapleCUN: added LaCrosse
- MapleCUN: added HMS Device Emulation for LaCrosse
- miniCUL: added Optiboot bootloader
- rpiaddon: added OneWire

#### 1.26.02
- MapleCUN/CUBe: add UART HAL
- MapleCUN/CUBe: increase MAX_CREDIT to 3600
- MapleCUN: Move serial console to DBG UART if USB is not connected
- MapleCUN: Some bugfix

#### 1.26.01
- MapleCUN/CUBe: Fix SlowRF/ethernet keepalive

#### 1.26.00
- Add I2C slave
- Add I2CCUL: Example device for communication over I2C

#### 1.25.02
- megaCUL: changed buffer size

#### 1.25.01
- MapleCUN: Fix baud rate setting command

#### 1.25.00
- ARM Models: 
  - Add onewire
  - Improve hardware autodetection
- MapleCUN: Add 3rd SlowRF transceiver

#### 1.24.02
- Add CC113L to hardware autodetection
- Fix tcp_putchar
- Fix MBUS for multi CC1101 devices

#### 1.24.01
- MapleCUN: Add bootloader

#### 1.24.00
- ARM Models: 
  - Rework of multi CC1101
  - Add RF mode switching
  - Add hardware autodetection
- MapleCUN: Add W5500

#### 1.23.09
- Add new device: megaCUL
- megaCUL: disabled by default: Honeywell evohome
- miniCUL: Code cleanup
- miniCUL: disabled by default: Honeywell evohome, M-Bus, ZWave
- rpiaddon: Code cleanup
- rpiaddon: disabled by default: Honeywell evohome

#### 1.23.08
- miniCUL: added Hoermann send + RFR Filter
- miniCUL: Code cleanup
- rpiaddon: added Hoermann send + RFR Filter

#### 1.23.07
- ARM Models: fix MBus

#### 1.23.06
- FIX: Remove LED flicker
- Use include-what-you-use (and some manual fixes) to fix many header includes.

#### 1.23.05
- CUBe: fix rf_native 

#### 1.23.04
- MapleCUL/MapleCUN: 
  - Access of UART2+3 via USB/network
  - Add multi CC1101 support
  - Activate Hoermann send
- ARM Models: add HAL

#### 1.23.03
- Hoermann Send (activated for CUBe + CUL-HM-CFG)

#### 1.23.02
- Fix IT V3 Dimmer - send mode

#### 1.23.01
- Fix nanoCUL device
- Fix miniCUL flash Skript
- Change sending for IT V1 D bit (Unitec/Intertek)

#### 1.23.00
- Support for EIM-826 (Unitec/Intertek) (Forum #48515 and #45022)
- Code upgrade from culfw Version 1.67 (2016-11-26)
- Hoermann Send (activated for CUL + nanoCUL)
- RFR filter: ufKERV forwards only messages starting with one of KERV
- intertechno: modify interval
- ZWave: no ack for routed packages (work in progress)
- RFR: do not report FHT if T01 is zero and RFR target is on (Forum #50756)

#### 1.22.00
- Add STM32 support 
- Add new device: MapleCUL/MapleCUN

#### 1.21.02
- miniCUL: added MULTI_FREQ_DEVICE in the board definition

#### 1.21.01
- Fix define dependencies 
- Add CUL-ProMini with 8Mhz)

#### 1.21.00
- Fix receive of GT-WT-02

#### 1.20.08
- Fix flash scripts
- Fix build errors

#### 1.20.07
- rpiaddon: Code cleanup 
- rpiaddon: added ZWave

#### 1.20.06
- miniCUL: Code cleanup 
- miniCUL: added more protocols (e.g. Belfox, Hoermann, Kopp FC, Somfy)

#### 1.20.05
- Code upgrade from culfw Version 1.66 (2015-11-29)
- CULV3/V4: add ZWave receive
- ZWave: receive+send @ 40k, 100k
- Cw: Write CC1101 register directly
- ZWave: receive+send(?) @ 9600

#### 1.20.04
- CUBe: Move serial console to UART0 if USB is not connected
- ARM Models: Remove malloc
  
#### 1.20.02
- Make the Intertechno send compatible to original culfw. 
  The default clock is now 420

#### 1.20.02
- Add the functionality to change ITClock of the Intertechno V1 protocol. The command is ic. Default is ic250

#### 1.20.01
- ARM Models: Add kopp-fc, rf_native, MBUS and ZWave protocol
- Check for manchester and IT protocol only when receiving 433MHz

#### 1.20.00
- Implement receive of Manchester coded signals linke Oregon2, Oregon3 or Hideki
- Enable receive of revolt for all devices
- Change IT V1 send timing to old 1.05.01 timing

#### 1.10.02
- Fix ethernet on CUBe
- Fix UNKNOWNCODE ZERR30D (Forum #332883)

#### 1.10.01
- Fix receiving of revolt for all devices.

#### 1.10.00
- ARM Models: Fix bootloader for AT91SAM7 REV C
              Activate 433MHZ protocols
- Rewrite of receive method for TCM/IT/HE
  Receive the protocolls more stable
  Receive additional sync protocols like Eurochron EAS800
- Change receive datarate in slowrf to 5,603 kBaud.
  (You must make a reset of the cul eeprom, use command 
  "set CUL-NAME raw e" in fhem)
- Fix receiving of revolt.

#### 1.05.04
- ARM Models: Add ethernet, add multi CC1101 support
- Code Cleanup

#### 1.05.03
- Fix timing for IT-V1 sending and receive timing for temp sensors

#### 1.05.02
- Revert timing for Elro AB440 IT Switch changes

#### 1.05.01
- Fix timing for Elro AB440 IT Switch
- Fix size for nanoCul

#### 1.05.00
- CULV3: add belfox (Forum #36810)
- CUN*: retransmit patches from doubh (Forum #36529)
- CUL: due to mem space issues: disabled by default: RF_RWE / MBUS_TX
- added RF-Native Mode for RFM12 based protocols i.e. LaCrosse/IT+/PCA302,
  ie.  use "Nr1" 
- add Bff to test the watchdog (Forum #36215)
- CUNO2: added SOMFY RTS support to board definition (thdankert)
- completed wireless m-bus RX/TX support (for T or S mode)

#### 1.04.01
- Implement sending for HomeEasy EU protocol (command ie<value>)

#### 1.04.00
- Implement sending for HomeEasy HE800 protocol (command ih<value>)
- Receive HomeEasy protocols

#### 1.03.04
- Reenable IT-Sending with CUL 868Mhz version
- Change IT receive and sending timing to make it more stable
- Cleanup code to reduce memory usage

#### 1.03.03
- From culfw: add Bff to test the watchdog (Forum #36215)
- From culfw: CUNO2: added SOMFY RTS support to board definition (thdankert)
- Fix size of 868MHz CUL (disable Hoermann, disable IT-Sending with 868Mhz 
  version)

#### 1.03.02
- Enable Oregon3 in CUL for testing

#### 1.03.01
- Split CULs in 433MHz and 868MHz version
- Implement Oregon 3, disabled by default. Define HAS_OREGON3

#### 1.02.02
- completed wireless m-bus RX/TX support (for T or S mode)

#### 1.02.00
- receive of other temperatur sensors like Rubicon and Prologue
- Cleanup some code

#### 1.01.00
- add support for intertechno v3 dimmer

#### 1.00.01
- Bugfix in rf_receive

#### 1.00.00
- Receive for TCM sensors like No.97001, No.212836
- Send/receive for IT Protocoll 1 and 3
- Cleanup of receive methods 
- Additional devices like miniCul, nanoCul, CUL-Arduino