Skip to content

Latest commit

 

History

History
 
 

qos

Implementing QOS

Introduction

The objective of this tutorial is to extend basic L3 forwarding with an implementation of Quality of Service (QOS) using Differentiated Services.

Diffserv is simple and scalable. It classifies and manages network traffic and provides QOS on modern IP networks.

As before, we have already defined the control plane rules for routing, so you only need to implement the data plane logic of your P4 program.

Spoiler alert: There is a reference solution in the solution sub-directory. Feel free to compare your implementation to the reference.

Step 1: Run the (incomplete) starter code

The directory with this README also contains a skeleton P4 program, qos.p4, which initially implements L3 forwarding. Your job (in the next step) will be to extend it to properly set the diffserv bits.

Before that, let's compile the incomplete qos.p4 and bring up a network in Mininet to test its behavior.

  1. In your shell, run:

    make

    This will:

    • compile qos.p4, and
    • start a Mininet instance with three switches (s1, s2, s3) configured in a triangle. There are 5 hosts. h1 and h11 are connected to s1. h2 and h22 are connected to s2 and h3 is connected to s3.
    • The hosts are assigned IPs of 10.0.1.1, 10.0.2.2, etc (10.0.<Switchid>.<hostID>).
    • The control plane programs the P4 tables in each switch based on sx-runtime.json
  2. We want to send traffic from h1 to h2. If we capture packets at h2, we should see the right diffserv value.

Setup

  1. You should now see a Mininet command prompt. Open two terminals for h1 and h2, respectively:
    mininet> xterm h1 h2
  2. In h2's XTerm, start the server that captures packets:
    ./receive.py
  3. In h1's XTerm, send one packet per second to h2 using send.py say for 30 seconds. To send UDP:
    ./send.py --p=UDP --des=10.0.2.2 --m="P4 is cool" --dur=30
    To send TCP:
    ./send.py --p=TCP --des=10.0.2.2 --m="P4 is cool" --dur=30
    The message "P4 is cool" should be received in h2's xterm,
  4. At h2, the ipv4.tos field (DiffServ+ECN) is always 1
  5. type exit to close each XTerm window

Your job is to extend the code in qos.p4 to implement the diffserv logic for setting the diffserv flag.

Step 2: Implement Diffserv

The qos.p4 file contains a skeleton P4 program with key pieces of logic replaced by TODO comments. These should guide your implementation---replace each TODO with logic implementing the missing piece.

First we have to change the ipv4_t header by splitting the TOS field into DiffServ and ECN fields. Remember to update the checksum block accordingly. Then, in the egress control block we must compare the protocol in IP header with IP protocols. Based on the traffic classes and priority, the diffserv flag will be set.

A complete qos.p4 will contain the following components:

  1. Header type definitions for Ethernet (ethernet_t) and IPv4 (ipv4_t).
  2. Parsers for Ethernet, IPv4,
  3. An action to drop a packet, using mark_to_drop().
  4. An action (called ipv4_forward), which will:
    1. Set the egress port for the next hop.
    2. Update the ethernet destination address with the address of the next hop.
    3. Update the ethernet source address with the address of the switch.
    4. Decrement the TTL.
  5. An ingress control block that checks the protocols and sets the ipv4.diffserv.
  6. A deparser that selects the order in which headers are inserted into the outgoing packet.
  7. A package instantiation supplied with the parser, control, checksum verification and recomputation and deparser.

Step 3: Run your solution

Follow the instructions from Step 1. This time, when your message from h1 is delivered to h2, you should see tos values change from 0x1 to 0xb9 for UDP and 0xb1 for TCP. It depends upon the action you choose in Ingress processing.

To easily track the tos values you may want to redirect the output of h2 to a file by running the following for h2

./receive.py > h2.log

and just print the tos values grep tos h2.log in a separate window

     tos       = 0xb9
     tos       = 0xb9
     tos       = 0xb9
     tos       = 0xb9
     tos       = 0xb9
     tos       = 0xb9
     tos       = 0xb9
     tos       = 0xb9
     tos       = 0xb1
     tos       = 0xb1
     tos       = 0xb1
     tos       = 0xb1
     tos       = 0xb1
     tos       = 0xb1
     tos       = 0xb1
     tos       = 0xb1

Food for thought

How can we let the user use other protocols?

Troubleshooting

There are several ways that problems might manifest:

  1. qos.p4 fails to compile. In this case, make will report the error emitted from the compiler and stop.
  2. qos.p4 compiles but does not support the control plane rules in the sX-runtime.json files that make tries to install using a Python controller. In this case, make will log the controller output in the logs directory. Use these error messages to fix your qos.p4 implementation.
  3. qos.p4 compiles, and the control plane rules are installed, but the switch does not process packets in the desired way. The /tmp/p4s.<switch-name>.log files contain trace messages describing how each switch processes each packet. The output is detailed and can help pinpoint logic errors in your implementation. The build/<switch-name>-<interface-name>.pcap also contains the pcap of packets on each interface. Use tcpdump -r <filename> -xxx to print the hexdump of the packets.

Cleaning up Mininet

In the latter two cases above, make may leave a Mininet instance running in the background. Use the following command to clean up these instances:

make stop